LGMG SS0407EScissor Lift

Name: LGMG SS0407E
Brand: LGMG

Drive Mode

4x2

Gradeability

25%

Power Source

24V DC Electric

Overall Width

0.76m (2ft 6in)

OEM-Compatible PartsFast ShippingExpert Support

Product Overview

The LGMG SS0407E is a compact micro scissor lift designed for rental fleet durability and tight workspace access. With a 12ft platform height and ultra-narrow 30-inch width, this machine fits through standard doorways and into freight elevators with ease. The direct electric drive system provides longer battery life and requires minimal maintenance—a key advantage for rental operations. Universal components shared across the LGMG scissor lift range reduce parts inventory and simplify technician training. Swing-out component trays provide easy access for routine maintenance tasks like hydraulic fluid checks and electrical system inspection.

Key Features

Ultra-Compact 30-inch Width - Fits Standard Doorways
Swing-Out Component Trays for Easy Maintenance
Commonality with Other LGMG Scissor Models

LGMG SS0407E Buying Guide

LGMG SS0407E Parts & Service Buying Guide

The LGMG SS0407E is the 13-foot micro scissor that shows up everywhere ceilings are low and elevators are the only way up — the direct rival to the Dingli JCPT0607 class. It is light, simple, and worked hard, which means its failure profile is dominated by operator-contact components and the battery system rather than hydraulics.

What breaks first on the SS0407E

Battery & charging — a compact 24V pack in a machine that gets parked uncharged between jobs. Low-voltage faults top the SS0407E fault code list; load-test before replacing anything.
Pothole protection — the guards on a micro scissor sit close to the floor and collect debris. Deploy faults that block lift are usually mechanical, not electrical.
Platform controls — joystick assemblies and enable switches take the most cycles of any part on the machine.
Charger — onboard units fail more often on micro scissors that live on job-site generator power; verify AC supply quality before condemning the charger.

Diagnose first: all 20 SS0407E fault codes with causes and fixes.

Replacement cadence (rule of thumb)

| Component | Typical interval | |---|---| | Batteries | 2-3 seasons; water monthly, more often in summer | | Pothole guard switches | Inspect quarterly; clean linkage at every PM | | Joystick / enable switch | On drift or intermittent response | | Onboard charger | Verify output before replacement; typically 4-6 years | | Scissor bushings | On visible platform play |

Confirm serial number when quoting — LGMG shares components across the SS/AS micro range but revised harnesses mid-production.

Aftermarket vs factory parts

Stay factory-spec for: the control ECU and CAN-connected modules. Aftermarket-friendly: batteries, chargers (verify 24V algorithm), limit switches, joystick assemblies, bushings, tires.

China Lift Supply supplies OEM-compatible aftermarket parts for LGMG lifts — request a quote with your serial for confirmed fitment.

Related resources

All 20 SS0407E fault codes
LGMG troubleshooting hub — every LGMG model we cover
Cross-brand scissor lift fault code guide

Technical Specifications

Specification	Value
Drive Mode	4x2
Gradeability	25%
Power Source	24V DC Electric
Overall Width	0.76m (2ft 6in)
Platform Size	1.27m x 0.7m (4ft 2in x 2ft 4in)
Machine Weight	1,100kg (2,425lbs)
Working Height	5.6m (18.4ft)
Platform Height	3.6m (11ft 10in)
Platform Capacity	240kg (530lbs)

Download Full Specification Sheet (PDF)

Available Parts

Need Parts for SS0407E?

We have direct access to the complete LGMG parts catalog. Tell us what you need and we'll source it at competitive prices.

Customer Reviews

No reviews yet for the LGMG SS0407E. Operated or serviced one? Be the first to share how it holds up.

Fault Codes & Troubleshooting

Search for error codes displayed on your SS0407E to find causes and solutions. Click on any code to expand details.

Showing 20 of 20 fault codes

Code	Description	Solution	Guide
01	System Initialization Error	Restart device. If fault persists, replace ECU controller. Check all harness connections are secure before power-on.	View Guide
02	System Communication Error	Check connection between the communication line and other cables. Inspect CAN bus wiring. If fault persists, replace PCU or ECU controller.	View Guide
03	Model/Machine Code Error	Set proper machine options in ECU settings. Verify correct model is selected during initial setup or after controller replacement.	View Guide
05	ECU and BMS Communication Failure	Check if CAN bus connections are secure. Inspect lithium battery harness connections. May require battery pack replacement if connections are good.	View Guide
09	Invalid Pedal/Joystick Alarm	Release the pedal switch. Check pedal harness connection status for short-circuit or open-circuit. Replace joystick if signal is invalid at neutral.	View Guide
14	Motor Controller 1 Communication Failure	Check if CAN bus connections are secure. Verify correct electric drive type is configured. Inspect motor controller harness for damage.	View Guide
16	BMS Fault (Battery Management System)	Check if CAN bus connections are secure. Inspect battery pack connections. May require lithium battery replacement if BMS is faulty.	View Guide
18	Pothole Protection Error	Check whether the pothole protection is activated. Inspect pothole protection limit switch and wiring. Check lower limit switch and connections.	View Guide
27	Down Proportional Valve Fault	Check or replace the down proportional valve. Inspect valve wiring for damage or loose connections. Verify hydraulic pressure is within spec.	View Guide
31	Pressure Sensor Error	Check the pressure sensor wiring and connector. Verify correct machine option with overload detection is selected. Replace sensor if faulty.	View Guide
32	Angle Sensor Error	Check the angle sensor wiring and connector. Verify correct machine option with overload detection is selected. Recalibrate or replace sensor.	View Guide
36	Low Battery Alarm	Charge battery immediately. When battery is fully charged and alarm persists, check battery cable connections or replace ECU.	View Guide
60	Motor Controller Fault (General)	Replace the motor controller or contact manufacturer. Check all motor harness connections before replacement.	View Guide
68	Low Voltage Fault	Charge battery in time. When battery voltage is normal and fault persists, check cable connections or replace the ECU.	View Guide
71	Motor Controller Contactor Fault	Replace the motor controller contactor. Check contactor coil wiring for damage. Verify 24V supply to contactor.	View Guide
73	Motor Controller Overheated	Allow motor controller to cool down. Check for adequate ventilation around controller. Clean cooling fins. Reduce duty cycle if persistent.	View Guide
80	Exceeding 80% Load Warning	Platform is close to load limit. Do not increase load. Remove excess weight from platform to reduce load percentage.	View Guide
90	Exceeding 90% Load Warning	Platform approaching maximum load. Do not increase load further. Remove weight immediately to prevent overload lockout.	View Guide
LL	Tilt/Level Sensor Alarm (Machine Tilted)	Machine exceeds safe tilt angle. Move machine to level ground. Check tilt sensor wiring and calibration. Recalibrate if on level surface.	View Guide
OL	Platform Overload Alarm	Remove excessive loads immediately. Platform is above rated capacity. Machine will not lift until load is reduced below limit.	View Guide

Can't find your error code?

Our technical support team can help diagnose issues and recommend parts.

Keep Your SS0407E Running

ChinaLiftSupply stocks thousands of aftermarket and OEM-compatible parts for LGMG equipment. Get competitive pricing, fast shipping, and expert technical support.

Browse All LGMG Models