LGMG AS0808EScissor Lift

Name: LGMG AS0808E
Brand: LGMG

Drive Mode

4x2

Gradeability

25%

Power Source

24V DC 225Ah Electric

Overall Width

0.83m (2ft 9in)

OEM-Compatible PartsFast ShippingExpert Support

Product Overview

The LGMG AS0808E (also known as AS2632E) is a narrow-aisle 26ft electric scissor lift optimized for rental fleet operations in confined spaces. The larger 7.5ft platform with 3ft extension deck accommodates two workers with materials, increasing productivity on elevated tasks. Zero-emission battery operation makes this machine suitable for indoor applications including retail fit-outs, warehouse maintenance, and HVAC work. Swing-out component trays provide easy maintenance access for rental technicians, minimizing turnaround time between rentals. The direct electric drive system delivers consistent performance and reduced service requirements compared to traditional hydraulic drive systems.

Key Features

26ft Working Height - Narrow 32-inch Width
7.5ft Platform + 3ft Extension Deck
Swing-Out Component Trays for Fleet Maintenance

LGMG AS0808E Buying Guide

LGMG AS0808E Parts & Service Buying Guide

The LGMG AS0808E is a 26-foot electric slab scissor — the size class that does the most rental hours of any access machine. LGMG builds it on the same electrical architecture as the rest of the AS/SS electric range, so control-side spares pool nicely across a mixed LGMG fleet.

What breaks first on the AS0808E

Battery system — four 6V deep-cycles doing full-shift duty. Most low-voltage faults in the AS0808E code list trace to one weak battery, not the charger.
Pothole guards — standard rental wear; bent linkage from curbs and door thresholds.
Drive & steer — steer bushings and drive hub wear show up as wander and clunk before they throw codes.
Platform control box — joystick drift after 2-3 seasons is normal duty wear.

Replacement cadence (rule of thumb)

| Component | Typical interval | |---|---| | Batteries | 2-3 seasons rental duty | | Pothole linkage & switches | Quarterly inspection | | Steer bushings | Annual inspection; replace on measurable play | | Hydraulic oil + filter | Annually | | Platform control box | On persistent drift/dead functions |

Aftermarket vs factory parts

Factory-spec: ECU and proportional valve. Aftermarket-friendly: batteries, chargers, switches, bushings, seal kits, filters, tires.

Request a quote with model and serial — we confirm fitment before you order.

Related resources

Technical Specifications

Specification	Value
Drive Mode	4x2
Gradeability	25%
Power Source	24V DC 225Ah Electric
Overall Width	0.83m (2ft 9in)
Platform Size	2.26m x 0.81m (7ft 5in x 2ft 8in)
Extension Deck	0.9m (3ft)
Machine Weight	2,140kg (4,718lbs)
Working Height	10m (32.8ft)
Platform Height	8m (26.2ft)
Platform Capacity	230kg (510lbs)

Download Full Specification Sheet (PDF)

Available Parts

Need Parts for AS0808E?

We have direct access to the complete LGMG parts catalog. Tell us what you need and we'll source it at competitive prices.

Customer Reviews

No reviews yet for the LGMG AS0808E. Operated or serviced one? Be the first to share how it holds up.

Fault Codes & Troubleshooting

Search for error codes displayed on your AS0808E to find causes and solutions. Click on any code to expand details.

Showing 20 of 20 fault codes

Code	Description	Solution	Guide
01	System Initialization Error	Restart device. If fault persists, replace ECU controller. Check all harness connections are secure before power-on.	View Guide
02	System Communication Error	Check connection between the communication line and other cables. Inspect CAN bus wiring. If fault persists, replace PCU or ECU controller.	View Guide
03	Model/Machine Code Error	Set proper machine options in ECU settings. Verify correct model is selected during initial setup or after controller replacement.	View Guide
05	ECU and BMS Communication Failure	Check if CAN bus connections are secure. Inspect lithium battery harness connections. May require battery pack replacement if connections are good.	View Guide
09	Invalid Pedal/Joystick Alarm	Release the pedal switch. Check pedal harness connection status for short-circuit or open-circuit. Replace joystick if signal is invalid at neutral.	View Guide
14	Motor Controller 1 Communication Failure	Check if CAN bus connections are secure. Verify correct electric drive type is configured. Inspect motor controller harness for damage.	View Guide
16	BMS Fault (Battery Management System)	Check if CAN bus connections are secure. Inspect battery pack connections. May require lithium battery replacement if BMS is faulty.	View Guide
18	Pothole Protection Error	Check whether the pothole protection is activated. Inspect pothole protection limit switch and wiring. Check lower limit switch and connections.	View Guide
27	Down Proportional Valve Fault	Check or replace the down proportional valve. Inspect valve wiring for damage or loose connections. Verify hydraulic pressure is within spec.	View Guide
31	Pressure Sensor Error	Check the pressure sensor wiring and connector. Verify correct machine option with overload detection is selected. Replace sensor if faulty.	View Guide
32	Angle Sensor Error	Check the angle sensor wiring and connector. Verify correct machine option with overload detection is selected. Recalibrate or replace sensor.	View Guide
36	Low Battery Alarm	Charge battery immediately. When battery is fully charged and alarm persists, check battery cable connections or replace ECU.	View Guide
60	Motor Controller Fault (General)	Replace the motor controller or contact manufacturer. Check all motor harness connections before replacement.	View Guide
68	Low Voltage Fault	Charge battery in time. When battery voltage is normal and fault persists, check cable connections or replace the ECU.	View Guide
71	Motor Controller Contactor Fault	Replace the motor controller contactor. Check contactor coil wiring for damage. Verify 24V supply to contactor.	View Guide
73	Motor Controller Overheated	Allow motor controller to cool down. Check for adequate ventilation around controller. Clean cooling fins. Reduce duty cycle if persistent.	View Guide
80	Exceeding 80% Load Warning	Platform is close to load limit. Do not increase load. Remove excess weight from platform to reduce load percentage.	View Guide
90	Exceeding 90% Load Warning	Platform approaching maximum load. Do not increase load further. Remove weight immediately to prevent overload lockout.	View Guide
LL	Tilt/Level Sensor Alarm (Machine Tilted)	Machine exceeds safe tilt angle. Move machine to level ground. Check tilt sensor wiring and calibration. Recalibrate if on level surface.	View Guide
OL	Platform Overload Alarm	Remove excessive loads immediately. Platform is above rated capacity. Machine will not lift until load is reduced below limit.	View Guide

Can't find your error code?

Our technical support team can help diagnose issues and recommend parts.

Keep Your AS0808E Running

ChinaLiftSupply stocks thousands of aftermarket and OEM-compatible parts for LGMG equipment. Get competitive pricing, fast shipping, and expert technical support.

Browse All LGMG Models